Water purifier FAQs and troubleshooting approach
2014/10/5 Views：1205
One problem, no water purifier problem
1, no power supply
When the power supply of pure water can not run out of power.
2, water dry / low water pressure
Water dry / low pressure switch does not open when the pressure is too low, it does not supply transformer.
3, the inlet valve did not open
Inlet valve did not open, no water entered the low pressure switch can not be opened.
4, the inlet valve bad
Solenoid valve open, water entrance, it can not water.
5, filter clogging
When the filter blockage, whether it is the front or rear of the core of the core, when the water can not be blocked.
6, clogging of the membrane / membrane dry
When the clogging of the membrane or film is dry, water may pass, can not water.
7, plumbing discounts
Discount when water flow blocking water pass.
8, the transformer bad
When the transformer is damaged can cause the inlet valve and the pump is not powered, you can not water
9, the pump bad
Bad pump, pressure hour, water can not pass RO membranes, can not water.
10, the low pressure switch is broken
When the low pressure switch will cause the transformer can not be a bad power supply, the machine can not run.
11, high pressure switch is broken
High pressure switch has been in the normally open state if not closed, the transformer can not supply.
12, cartridge joint raw material with improper wound
As raw material winding incorrectly, it may cause raw material with blocked filter connector can not pass water.
Question two, water purification machines out of water too small issues and troubleshooting
1, the water temperature is too low
When the water temperature is too low, water ice, was solid through the less.
2, filter clogging
When the filter blockage, whether it is the front or rear of the core of the core, when the water can not be blocked.
3, membrane clogging
When the clogging of the membrane or film is dry, water may pass, can not water.
4, the pressure tank no pressure or low pressure
Pressure tank no pressure or low pressure, the pressure barrel pressure is not out of the water but with the mechanism of water.
5, pressure tank valve did not open
When the pressure tank valve did not open, but with the mechanism of the effluent water, so less water.
6, plumbing discounts
Discount when pipes, water pipes inner diameter becomes smaller, the small amount of water through.
7, pump the water pressure is not enough
Pump water pressure hour, water RO membranes through a small amount
Question three, more dense water purification machines, has been ranked the concentration of water
1, bad power supply
Each time the machine is powered flush valve settings automatically flushing 18 seconds. Rinse repeatedly when the power is bad.
2, small pressure / pressure instability
When little pressure or pressure instability may lead to low-voltage switchgear frequent closed.
3, check valve bad
Check valve backflow role water plays ban, if the check valve through, pressure bucket of water will be returned to the concentrated water discharge pipe, water machine will start frequently, concentrated water discharge.
4, the flush valve bad
If the flush valve can not be closed, it would not achieve the effect of the concentration of water than the throttle, concentrated water discharge volume.
5, the concentration of water than bad
If the concentration of water than the damage will lead to action would not achieve the throttle, concentrated water discharge volume.
Question four, or other abnormal sound heard continuous noise problems and troubleshooting
1, pressure instability
Hydraulic instability may cause the machine to start frequently, continuous audible, when the water pressure (Smart) will (display) The display of water and the police.
2, low-voltage switchgear bad
A low-pressure switch is broken (Smart), can not be closed, it would have been the police.
3, high-voltage switch bad
The high pressure switch is defective, it may cause the machine (inlet valve) frequent start, emits a continuous sound.
4, the transformer seepage
Seepage inside the transformer may cause an internal short circuit, noise.
5, gas inside the pipe
The gas in the pipeline, it may issue a water pipe friction and impact sound machine.
Fifth, decreased taste
1, activated carbon core life to
Activated carbon adsorption of residual chlorine in the machine core play, the role of bacteria, viruses, such as adsorption saturation, can no longer taste will fall.
2, reverse osmosis membrane membrane tubes not installed or bad
Such as reverse osmosis membrane membrane tubes not installed or bad, the water is not flowing through the reverse osmosis membrane directly, poor taste.
3, a long time without the machine
If the machine long time, closure down bacteria, viruses may multiply in the filter, thereby affecting the life and the results filter.
Question six, water issues and troubleshooting high TDS value
1, the reverse osmosis membrane membrane tubes not installed or bad
Not installed as a reverse osmosis membrane or a membrane tube bad, the water is not flowing through the reverse osmosis membrane directly, so the high TDS value.
2, a long time without the machine
A long time without the machine, rear carbon impurities in the outflow when re-enabled.
3, to the rear of the core life
Rear carbon life to, adsorbate inside the filter is saturated, there may be some impurities flowing out, affect water quality.
Before using RO reverse osmosis water purifier should be noted
1. Make sure the unit operates at room temperature (5-40 ℃) conditions directly affect the size of the filter system water temperature.
2, raw water quality must be municipal tap water, poor water quality, the filter will advance blockage of filter life.
3, the machine must be carried out prior to the normal use of debugging operation, or tap water may have a fine black powder.
4, a long time without the machine should shut off the water supply when using the machine again, and for the first time should use the machine to debug operations, such as water quality is not ideal after cleaning, replace the filter as soon as possible.
5, should replace the filter cut off the power, and pay attention to the direction and order of the filter, and debugging operations should also be the first use of the machine after the same filter replacement.